一、性状

1、外观：白胶浆白色糊状，透明浆淡黄色糊状；

2、组成：环保特软高弹树脂、进口助剂同钛混合而成；

3、离子性：非离子性；

4、粘度：140000-150000CPS；

5、PH值：7-8。

二、特性

1、本产品具有手感柔软，高弹力，高遮盖，水洗牢度好，印刷性好，不塞网，不反粘，表面光滑，阻燃效果强，安全等特点。

三、适用范围：适合于各类防火布料印花，棉布，T/C布，麻涤晴毛圈织物及其混纺拉架布等织物。

四、使用方法

1、本品一般使用100-120目丝网，根据不同图案使用不同目数；

2、本产品使用后可自然干燥24时或经过烘道（干燥机）130℃度过热2-3分钟；

3、印完后烘道完全烘干，即可马上洗水。其洗水牢度同弹性可与同类胶浆比美。

五、注意事项

1、自然干燥时间与气温和空气湿度有关；

2、储存期：在室温下密闭可存放一年以上，仓库内要阴凉、干燥、通风；

3、使用后内袋应该重新扎实，以防暴露在空气中造成结皮；

4、调色可根据客户需要颜色的深浅来调入色种的分量，颜色调入太多容易引起掉色现象，色种最好控制在5%之内；

5、如印容易掉色的深色布，需要测试颜色是否会升华到胶浆表面上，以减少不必要的损失；

6、使用本产品印花，必要时要进行白胶浆和透明浆相调及搅匀印刷，以免出现裂纹及手感软弱度差的现象；

7、使用透明浆印花，要稍加白胶浆掺和进行调色印花有利于在纺织品面料上印花着色度饱和，更好发挥透明浆的应用效果。

8、本产品操作使用说明书仅提供参考意见，须生产者根据自身生产状况进行试样测试，测试效果可以后方可进入大量生产。

一、Character

1、Appearance：white mushy of white base,slight yellow mushy of clear base

2、Composition:environmental soft elastic resin、imported auxiliary;

3、Ionic type:Non-ionic

4、Viscosity:140000-150000CPS

5、PH value:7-8

二、Characteristic

1、Soft hand feel,high elasticity,high covering power,good wash fastness, no plug mesh,no inverse stick,smooth surface,good flame-resistant effect,safe.

三、Scope of application

Various types of fire-resistant fabric,cotton,T/C,flax and terry and so on.

四、Usage

1、This products to be printed with 100-120 mesh screen usually,however,according to different pattern use different mesh;

2、After printing,drying by it self naturally for 24 hours or through drier at 130℃ for 2-3 minutes;

3、After printing and then drying completely,can be washed instantly.Its wash fastness and elasticity can compare with same series of pastes.

五、Notes

1、The time of drying depends on temperature and air humidity;

2、Shelf-life:sealed store at room temperature over than one year,the storehouse should be cool、dry and well-ventilated;

3、After using,the inner bag should be firmed again,avoid to cause crust which is exposed to air;

4、According to customers’needs for intensity of color to add amount of pigment,adding too much pigment will easy to cause phenomenon of discoloring,the amount of pigment best to control into 5%;

5、If print on the dark fabric which is easy to fade,should make a test about the color whether sublimate on the appearance of paste,in order to reduce losses;

6、Using this product to print,when necessary,mixing white base and clear base to stir well and print,avoid to appear the phenomenon of cracking and affect its hand feel;

7、Using clear base to print,should add little white base to adjust color,which is beneficial to saturation of dyes and [lay best applied effect of clear base;

8、This operation specification just for reference only,should make a test by customers themselves,if the results of test are ok then make mass production.